Metal Scrap Briquetting Baler
This metal scrap briquetting baler is ideal for compressing small metal items like oil filters, aluminum cans, steel food cans, and iron chips. With high pressure force, compact chamber, and automatic sliding door, it forms tight square blocks without the need for strapping or bagging. Fully PLC-controlled, it operates automatically—from detecting full load to compressing and ejecting. Optional conveyor enables auto feeding. Perfect for metal manufacturers, collectors, and recyclers, it offers over 10:1 compression, saving space and maximizing ROI.
Product description
This metal scrap briquetting baler is specialized in baling small item metal scraps, including metal oil filters, aluminum cans, steel food cans, iron chips, etc.. Hence, it is also known as oil filter briquetting baler, metal can briquetting baler … Attributed to its high pressure force, compact compression room as well as a sliding door installed at the output chute, those metal scraps can be crushed into tight square blocks, no need any strapping or bagging to hold the blocks.
It is a fully automatic machine controlled by PLC system, efficient and labor saving. Once the machine gets a signal that the compression chamber is fully filled, the compression cylinder will automatically travel downward to start crushing, and thereafter when the compression cylinder returns to the upper position the ejecting cylinder will automatically start pushing forward horizontally. The hydraulic-driven sliding door at the output will automatically open once the pressure of the ejecting cylinder reaches the maximum, and after that the block is pushed out by the ejecting cylinder. A feed conveyor can be connected with the baler to reach automatic feeding through the interlocking system between the baler and conveyor.
No matter you are a metal products manufacturer that generates scrap metal chips in big volume every day, a metal waste collector, or a recycler of steel cans or aluminum cans, this metal scrap briquetting machine is quite a necessary item for you to invest. Compression ratio of the machine can reach more than 10:1, which means it can greatly save the transportation space or storage room, and subsequently brings you much benefit and high ROI in long run.
We supply not only below standard unit, but can also custom make according to customer’s specific requirements in terms of productivity, block size, etc., as long as the requirements are reasonable enough. Contact us now and our sales representative will provide an ideal solution for your metal scrap recycling.
Choose from our various balers available, or contact us for a customized baling solution. View shredders.
Main Features
- Fully Automatic Operation System
enables automatic compressing & bale ejecting, making the machine rather efficient and labor saving - Liquid Drainage Tray
for receiving and draining out the residual liquid squeezed out from the filters or cans to keep the recycling area clean and safer - PLC Control System
automates the operation and promotes accuracy - Close-end Door
ensures all the scrap items are thoroughly compressed and the bales are firmly compacted - Electric Controlled
makes the operation easy and convenient – simply by pressing the buttons to control the machine - Feed Conveyor is Optional
for automatic feeding material into the baler through the interlocking system between the baler and the conveyor
Specifications
| Model | Bale size | Bale weight | Throughput | Strapping | ||
|---|---|---|---|---|---|---|
| Length | Width | Height | ||||
| SHB1-WSB-F-1000A |
L mm ( inch) |
300 mm (12 inch) |
300 mm (12 inch) |
2~25 kg (4.4~55 lbs) |
60 bales/hr |
N/A |
| SHB1-WSB-F-1000B |
L mm ( inch) |
300 mm (12 inch) |
300 mm (12 inch) |
2~30 kg (4.4~66 lbs) |
60 bales/hr |
|
RELATED VIDEO
BALING Applications
Oil filters, steel cans, aluminum cans, iron chips, small metal containers.
RELATED Baler Accessories
FAQ about this machine
It is important that clean hydraulic oil is in the pump before running the machine in order to lubricate the bearings and transmission system.
Therefore, do check the pump once you filled up the oil tank, steps as follow:
• Unscrew and remove the oil pipe joint using a wrench.
• Once joint and oil pipe is removed, you can see the oil discharge opening. Fill hydraulic oil through the opening until it is full to the brim. (If there is air in the pump, it will create loud noise when you run it, which might cause damages)
• Reconnect the oil pipe and ensure the joint is tightly fastened.
Upon releasing your baling machine from our factory, we will indicate the required amount of hydraulic oil based on your working condition and environment temperature, and reflect it as Best Oil Level for your baler.
You can easily refer to the “Best Oil Level” stickers as a gauge when you are filling up the oil tank and conduct regular checks on oil level (as seen on picture, slight variation above or below the level line is acceptable).
Taking into consideration that actual operation hours and conditions may varies from time to time, regular checks on oil temperature and level is strongly recommended.
Best Oil Level sticker
I agree that my personal data collected by SINOBALER is processed, used and stored in compliance with data protection exclusively for the purpose of processing my request.
Media and Gallery
Follow us
PRIVACY POLICY
We collect information from you when you fill out an inquiry or contact form. When submitting the form on our site, you may be asked to enter your name and contact details such as: e-mail address, mailing address and/or phone number, etc. Alternatively, you can choose not to complete our forms and visit our site anonymously. Any of the information we collect from you may be used to help us to better respond to your individual needs, and/or enable us to more effectively respond to your customer service requests and support needs. The email address you provided may also be used to send you information and updates pertaining to your inquiry and/or order, in addition to receiving occasional company news, updates, related product or service information, etc. SINOBALER does not sell, trade, or otherwise transfer to outside parties your personally identifiable information. This does not include trusted third parties who assist us in operating our website, conducting our business, or servicing you, so long as those parties agree to keep this information confidential. We may also release your information when we believe release is appropriate to comply with the law, enforce our site policies, or protect ours or others rights, property, or safety.
By using our site, you consent to our online privacy policy. If we decide to change our privacy policy, we will post those changes on this page. If you have any questions or concerns regarding our privacy policy, please e-mail info@sinobaler.com or mail your question to us at 1206 Yinzhou Shanghui Nan Lou, 1299 Yinxian Avenue, Yinzhou District, Ningbo 315192, P.R. China.
EXTERNAL LINKS & DISCLAIMER
Our web site has links to many other organizations with their permission. Upon leaving the SINOBALER web site, you are subject to the privacy policy of the new site which are not under our control. SINOBALER is not responsible for the content of any linked site or any link contained in a linked site. These links are provided to you as a service for you to better understand the different business relationships that SINOBALER has established, and/or to point the reader to other possible relevant resources.